If you have a broken garage door torsion spring, it can be a real pain to fix. Many people don’t know how to do it themselves, and have to call in a professional. In this blog post, we will walk you through the step-by-step process of replacing broken garage door torsion springs. We will provide you with all of the information you need to get the job done safely and efficiently. So don’t wait any longer – read on for instructions on how to replace your broken garage door springs!
The first step is to disconnect the garage door from the opener. This can usually be done by pulling on a release cord that is attached to the door. Once the door is disconnected, you will need to remove the bottom bracket that holds the spring in place. This can be done with a wrench or socket set.
Once the bottom bracket is removed, you will be able to access the springs. Carefully remove the old springs and discard them. It is very important that you do not touch the coils of the new springs, as they can be extremely dangerous.
Next, carefully install the new springs by following the same steps in reverse. Make sure that the springs are properly aligned, and that the bottom bracket is securely in place. Once everything is in place, reconnect the garage door to the opener and test it out!
How much does it cost to replace a torsion spring on garage door in Pittsburgh?
The cost of replacing a torsion spring on garage door in Pittsburgh can vary depending on the type of spring you need and where you purchase it from. You can expect to pay anywhere from $50 to $200 for a single spring. If you need to replace both springs, the cost will be double. Many hardware stores sell torsion springs, but you may also be able to find them online. Be sure to compare prices before making your purchase.
Replacing broken garage door torsion springs can be a difficult and dangerous task. It is best to leave it to the professionals if you are not comfortable doing it yourself.
How do I lift my garage door with a broken spring?
If you have a broken garage door spring, you will not be able to lift the door. You will need to replace the broken spring before the door will operate properly. Many hardware stores sell torsion springs, but you may also be able to find them online. Be sure to compare prices before making your purchase. Garage door springs should only be replaced by a professional.
How do you remove a broken torsion spring?
Broken torsion springs can be very dangerous. It is best to leave it to the professionals if you are not comfortable doing it yourself. Many hardware stores sell torsion springs, but you may also be able to find them online. Be sure to compare prices before making your purchase. Garage door springs should only be replaced by a professional.
What are the symptoms of a broken garage door torsion spring?
If you have a broken garage door torsion spring, you may notice that the door is difficult to lift or open. You may also hear a loud noise when the door is opened or closed. It is important to replace broken garage door springs as soon as possible to avoid injury. Many hardware stores sell torsion springs, but you may also be able to find them online. Be sure to compare prices before making your purchase. Garage door springs should only be replaced by a professional.
More useful information…
Is your garage door difficult to open? Or does it suddenly close when you try to open it?
Probably the reason why you’re having issues with your garage door is because of a broken spring.
While a DIY can help you fix your spring, you must know that it is a dangerous job.
Besides, the last thing you want to happen is suffering from injuries.
Garage door springs pretty much do all the hard work to keep your garage door operating.
However, it can be perplexing if they’re broken.
For this reason, we will guide you all about torsion springs, the reasons why they break, and how to replace a broken garage door torsion spring.
What is a Torsion Spring?
You’ll know when you have a torsion spring when you see it wraps around a tube shaft above the garage door opening.
Torsion springs are made of metal that is under high tension. Once you open the garage door, the tension releases from the spring.
Hence, it’s difficult once you try to fix a broken spring.
Springs under high tension can pose dangers.
If you’re adamant about replacing it yourself, it’s entirely possible as long as you’re an experienced do-it-yourself person.
However, the best advice is to leave the job to a garage door repair company near you.
Why Torsion Springs Break?
It has probably crossed your mind – why do torsion springs break?
Like other equipment, everything comes to last, and this is no exception with garage door torsion springs.
Hence, these are the reasons why it happens.
1. Wear and Tear
Most torsion springs last between 10,000 to 20,000 cycles, with one cycle equal to a garage door opening and closing.
When you think about it, it may seem like a lot of years before the springs break. However, when you’ve been using the garage door frequently, the sooner your springs get damaged.
If you have been using your garage door many times, check for wear and tear as it may happen sooner than you think.
Torsion springs are made of metal. Therefore, they are prone to rust.
When rusting occurs on the springs, it will affect their lifespan.
Rusting causes friction between the coils, and when this happens, it might lead to the failure of the springs.
Apply a silicone-based lubricant to the springs three to four times a year to deal with this problem.
In this way, it will allow the door operation to run smoothly while extending the springs’ life.
3. Lack of Maintenance
All garage door springs last a long time. Hence, you can lengthen the life of your springs by conducting regular maintenance.
Lack of maintenance can shorten the life of your springs leading to the door’s poor operation.
Make sure to check the condition of the springs for wearing, rust or damage. Lubricate the springs if they have shown signs of corrosion.
You can also test the door’s balance by manually opening the door using an emergency release cord. Operate the door until it’s halfway open.
When the door does not sag, the spring is in good condition. Otherwise, the spring is likely damaged when the garage door sags.
With this, leave the job to the professionals in Pittsburgh for garage door springs replacement.
How to Replace Broken Torsion Springs?
Before you attempt to fix the torsion spring, spot these indicators on garage doors:
Overhead door does not open: If the door refuses to open, the springs have lost the tension needed to pull the garage door up.
Overhead door is difficult to open: If you press the remote to open the door, and the door only raises for a few inches, the springs are likely broken. Check the issue with an emergency garage door service in Pittsburgh to fix it.
Overhead door seems to sag when closing: If you open the door and it suddenly closes, the springs are having difficulty due to tension problems. Inspect the issue with a professional before the damage gets worse.
Overhead door is producing loud noise: Hearing a loud bang on overhead doors can make you jump and disturb your neighbors. Call a professional to inspect the problem.
When you encounter the above signs, you can finally call for the repairs.
If you’re competent enough to repair yourself, watch this video on how to replace a broken garage door torsion spring.
DIY vs. Professional?
While DIY can save you money, it’s best to ask a professional to help you do the job correctly.
Leaving the job to the experts will not only save you from trouble and injuries, but you can receive warranty offers to save money in the long-term.
If you want to know more tips and advice on how to replace a broken garage door torsion spring, call Garage Door Pitt. Or, you can leave the repairs to us!